*FIRST OF ALL I AM NOT TRYING TO PROMOTE COMPARE OR SELL ANY PRODUCT, I DO NOT HAVE ANY CONNECTION WITH THE MANUFACTURER*
So after the harsh winter and a few trip to the pothole-land NYC I pull the "trigger" on the CXRacing set on e-bay, delivery was very fast and the whole package was quite heavy.
So I bring the whole deal to the NEU BB-Q"R" in Vienna in order to have other people opinion.
After a complete check-up I bring them back home to install them.
Word of advise: spray with dw40 or similar all the suspension bolts/nuts on front/rear lift the car and drop'it ON JACK-STANDS ( DO NOT WORK WITH THE CAR ON THE HYDRAULIC JACK)
get a beer/soda and wait or clean the rims for a while 
I start with the sway link ,
then the ABS sensor in order to avoid any unwanted damages,
get loose the two big bolts (LEAVE ONE IN TO HOLD THE WHOLE SPINDLE)
support from underneath the spindle(disk/axle bearing ) in order to prevent from falling forward and damage the axle/brake hose.
now you can take the top 3 nuts off, slide out the big side bolt and carefully take out the heavy and rusty part.
THE NEW COILS. FRONT
Out of the box the front's are way shorter than stock shock/ipd black combination, only weight is almost the same.
do not get tricked by the length,out of box set up is very high.
I insert (screw in) the main cylinder until the bottom edge of the bracket holder, see pic
the silver circle is the bottom of the coil (still have apr 1 to 2 inch to get lower)
the coil is nicely painted/welded and for the biggest relax the sway link tab is positioned perfectly and welded professionally ,in short is STRONG!
after you choose your height tighten well the aluminium big nuts with the special keys that came with the set.
the coils fit perfectly in with no problems whatsoever, you crank up the jack/spindle until the links reach the tab
insert back the ABS sensor connector, tighten well the two big bolts, crank the jack a bit in order to install the 3 top nuts.
With the wheel on air or on to the ground (under full load) the gap in between the rim and strut/coil assembly still the same apr 1 inch with the Midir's 18x8 and 225/40 tires and 3/4 of inch with the OZ's 18x8 and same tires ALL this with the spindle assembly fully puled outward from top.
THE NEW COILS REAR
Take out FIRST the 18 mm on the bottom of the rear shock,
now take out the top 12 mm nut and have a pliers handy to hold the top.
take the 15 mm nut from under the spring seat, push downward with your foot the whole assembly brake/disk/hub and with a pry bar push out the old spring (do not put your bare hand down there, spring might still under load) IF YOU DO ITS UP TO YOU or your skin
on the CXRacing rear coilover the adjustable spring perch stay on TOP!
Shock is adjustable too ( I choose a bit higher set up do to running a temporary set of wheels )
Install on revers like the stock ones, perch with big washer and 17mm bolt/nut go on the bottom install this one FIRST on the spring area!
My car set-up:
front IPD track sway bar connected on the street load, IPD sway links, IPD cherry strut tower bar.
rims OEM 2013"MIDIR" 18 x 8 ET60? with 225/40 ventus tires.
First thing you will notice is that when you sit on the car the body of the car will not move/lower at all!!!
After the first test drive I can tell you the car is flat on the corners at any "legal" street speed, traction is way better than previous set-up and you will feel almost any road imperfection if you choose the extremely rigid bounce set-up!!!
I DO NOT HAVE any rubbing front or rear with the actual set-up high wise, with two people on the car and the trunk heavily loaded.
Working on the other pictures at the moment, hope this help others to understand better the safety/performance upgrade that a set of coilover bring to our cars!!!
Please keep the comments strictly related to the topic, if you can will excuse my grammar/language and length of this post !!! Ciao Tizio.
